|
Joined: Aug 2003
Posts: 353
Contributor
|
OP
Contributor
Joined: Aug 2003
Posts: 353 |
Hi, Anyone know of a online chart of carburetor base dimensions? Something like the engine swap charts.
At this point looking for the baseplate size of a Holley 5200 two barrel.
Thanks
Pete 64 Chevelle 61 C30 Panel truck
|
|
|
|
Joined: Apr 2003
Posts: 1,537 Likes: 15
1000 Post Club
|
1000 Post Club
Joined: Apr 2003
Posts: 1,537 Likes: 15 |
Hi Chevelle292Wagon . . . I find the articles over at The Carburetor Shop instructive. They have a nice write up on the differences in four barrel mounting flanges. As for the Holley 5200 - I believe those were native on Fords. The flange bolt pattern is both wider and longer then a Rochester dual jet: Holley makes an Adapter Plate image above. No experience here beyond way to much time researching on the web . . .
|
|
|
|
Joined: Oct 2009
Posts: 471 Likes: 9
Contributor
|
Contributor
Joined: Oct 2009
Posts: 471 Likes: 9 |
yes, holly 5200's were found on Ford Pinto's among others (also vega and a few others). They are a weber carb that weber licensed to holley during those years. They are a 32/36 mm progressive two bbl. They work pretty well on an inline motor, even with an adapter (2 to 1), better without adapters or the above adapter. Not sure of the dimensions, but not the same as any rodchester, or holley 2300 series 2 bbl. I like the 1974 model, threaded fuel inlet as opposed to the earlier pressed in brass nipple inlet. If you use them, make sure you install the carbs so that the main jets are pointed forward. The are installed in a corner of the fuel bowl and will uncover on hard acceleration leading to a big giant bog (ask me how I know, lol)
If you have a really modified motor, then its the DGEV 38 mm two bbl. larger then the 32/36, a little more expensive, and not a progressive carb. Not really adapter friendly because of their size. but runs like heck.
Last edited by mdonohue05; 11/06/17 01:15 PM.
|
|
|
|
Joined: May 2011
Posts: 378
Contributor
|
Contributor
Joined: May 2011
Posts: 378 |
>If you have a really modified motor, then its the DGEV 38 mm two >bbl. larger then the 32/36, a little more expensive, and not a >progressive carb. Not really adapter friendly because of their >size. but runs like heck.
thats what I'm doing now, see my other thread from yesterday. Found a Weber 38/38 clone cheap, "Rally" something or another.
I feel it a little pointless to put a much bigger carb on a stock intake, choking it down to original size after the carb. Might help a little, don't know.
Its not easy to make the stock intake noticeably bigger, you quickly punch a hole into the exhaust chamber around it. Knowing this, I got a spare intake to learn more, and found a way to make it 46% bigger.... by using a steel sleeve once I made the hole a LOT bigger. Not for someone who is not comfortable doing metal work or paying a machine shop a lot of money, easily more than a new clifford or offy intake would cost.
Commercially available adapters are super cheap, but cast in a way that makes it impossible to make them noticeably bigger. They are tall too, which may cause hood clearance issues. The pattern mine has (Only one I know to be available everywhere) is NOT the same pattern as the Weber 38/38. It matches with the Rochester 2bbl and a few other domestic 2bbl carbs. Those might still work reasonably well, in a mild engine, even if smaller than the 38/38. I didnt care to find out.
Edit: isn't the 292 original intake bigger than the 230/250 intake?
Last edited by 70Nova; 11/06/17 01:39 PM.
|
|
|
|
Joined: Jan 2005
Posts: 2,123 Likes: 3
1000 Post Club
|
1000 Post Club
Joined: Jan 2005
Posts: 2,123 Likes: 3 |
AFAIK the Rochester Model B throttle bore for the 292 is 1-3/4", larger than the 230 although it uses the same #3 SAE flange.
|
|
|
|
Joined: Aug 2003
Posts: 353
Contributor
|
OP
Contributor
Joined: Aug 2003
Posts: 353 |
Pete 64 Chevelle 61 C30 Panel truck
|
|
|
|
Joined: Aug 2003
Posts: 353
Contributor
|
OP
Contributor
Joined: Aug 2003
Posts: 353 |
Edit: isn't the 292 original intake bigger than the 230/250 intake? I believe the throttle bore is the same on 194-292 manifolds. The ones I have measure 1 13/16. The 194 intake, however, has noticeably smaller runners. see pic: [img:center] https://imgur.com/bcmqYP9[/img]
Last edited by Chevelle292Wagon; 11/09/17 11:51 AM.
Pete 64 Chevelle 61 C30 Panel truck
|
|
|
|
Joined: May 2011
Posts: 378
Contributor
|
Contributor
Joined: May 2011
Posts: 378 |
thanks, I have to compare mine
|
|
|
|
Joined: May 2011
Posts: 378
Contributor
|
Contributor
Joined: May 2011
Posts: 378 |
Figures, I did all that work on the smaller intake Should help velocity and low end though... haha.
|
|
|
1 members (stock49),
26
guests, and
30
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|